Electronic Integrated systems Mechanic

Department of Defense Jacksonville, FL
* Duties

Help Duties Summary

This National Guard position is for a ELECTRONIC INTEGRATED SYSTEMS MECHANIC, Position Description Number D2240P01and is part of the FL 125th FW, National Guard.

INTRODUCTION: This position works within an Air National Guard Aviation Wing. The primary purpose of this position is to install, modify, overhaul, maintain, troubleshoot, repair, align, calibrate, and rebuild multi-system avionics complexes.

Learn more about this agency

Responsibilities

As a ELECTRONIC INTEGRATED SYSTEMS MECHANIC, WG-2610-12/13, you will perform scheduled and unscheduled maintenance on one or more multi-complex electronic integrated systems. Complete operational checks, inspections, tests, trouble shooting, removal and replacement of Line Replaceable Units (LRUs) which are linked with integrated systems and LRUs which are independent or associated with nonintegrated systems. Review and analyze maintenance data; determine if criteria are sufficient to provide adequate test, troubleshooting and repair procedures; devise and recommend tests, procedural changes, or data corrections. Troubleshoot operational malfunctions and analyze system performance utilizing aircrew debrief data, Technical Orders, schematic and wiring diagrams, engineering drawings, data analysis, common and system-specific test equipment and built in system tests. Recommend methods to improve equipment performance, technical data, and maintenance procedures by reporting hardware and software malfunctions, initiate material deficiency reports both on equipment and in technical data, and assist in design changes as necessary. Conduct on-the-job training on assigned systems and related support equipment and tasks to include classroom instruction as necessary. Comply with safety, fire, security, and housekeeping regulations.

PHYSICAL EFFORT: Light to moderate physical exertion is required in lifting and carrying items weighing from 10 to 40 pounds and occasional objects weighing in excess of 40 pounds. Mechanics are required to stoop, bend, and stand for extended periods of time on concrete or composition floors and work in tiring and uncomfortable positions. Heavy lifting is accomplished with assistance.

WORKING CONDITIONS: Work is primarily performed inside in well lit, heated, and ventilated areas. Occasionally, work may be performed on aircraft in high, restricted or confined places, and in environmental conditions of heat/cold and outside inclement weather. Incumbent is continuously subjected to hazards such as electrical shock, cuts, bruises, high intensity burns caused by electrical, RF energy, soldering irons, and explosive detonation from chaff/flares. Due to the requirement to upload and download chaff/flare dispensers, incumbent is involved in the storage, inspection, handling of explosive devices and works in a high noise and dangerous explosive environment.

Travel Required

Occasional travel - You may be expected to travel for this position.

Supervisory status

No

Promotion Potential

13

* Job family (Series)

2610 Electronic Integrated Systems Mechanic

* Requirements

Help Requirements Conditions of Employment

* Security Clearance requirements are determined by position and/or MOS/AFSC compatibility.

* APPLICANTS SHOULD CONTACT THEIR STATE INCENTIVES MANAGER TO DETERMINE IF ACCEPTING THIS POSITION WILL AFFECT ANY BONUS RECEIVED FROM THE MILITARY.

* Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.

* This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.

* Participation in direct deposit is mandatory.

* Selectee will be required to wear the military uniform.

* May be required to successfully complete a probationary period.

* Federal employment suitability as determined by a background investigation.

* Males born after 31 December 1959 must be registered for Selective Service.

* National Guard Membership is required.

Qualifications

AREA OF CONSIDERATION: This position is in the Excepted Federal Civil Service "under the authority of 32 U.S.C. 709", and is open to Category 1: All permanent/indefinite (T32 and T5) technicians employed by the agency Category 3: All current military members of the Florida National Guard; and Category 4: All individuals who qualify for membership in the Florida National Guard and are willing to become T32 Dual Status technicians. First consideration will be given to Category 1.

PCS: Permanent Change of Station (PCS) costs or Relocation Incentive MAY be authorized. Authorization for payment of PCS expenses or Relocation Incentive will be granted ONLY after determination is made that payment is in the best interest of the Florida National Guard.

Military Grades: Enlisted- E6 and Below

Compatible Military Assignments: AFSC: 2A071, 2A271/272/273, 2A374/375, 2A871/872, 2A971/972/973, 2A051, 2A031, 2A251/252/253, 2A231/232/233, 2A354/355, 2A334/335, 2A851/852 2A831/832, 2A951/952/953, 2A931/932/933.

GENERAL EXPERIENCE: Must have experience or training which demonstrates knowledge of electronic theories and practices to identify, isolate and repair malfunctions in one or more complex integrated systems where knowledge of the entire system is necessary to interpret error data and trace back through a number of units of the system to locate deficiencies; thorough knowledge of principles of digital and analog circuits, electro-mechanical devices, solid state devices, digital techniques, synchro/servo operation and integrated circuit theory; ability to interpret and trace schematics, logic and wiring diagrams and use a wide variety of test, measurement, and diagnostic equipment (TMDE).

SPECIALIZED EXPERIENCE: WG-12 must have at least a Three-Skill Level in one of the compatible AFSCs, with 12 months of work experience, that involved installing, modifying, overhauling, maintaining, troubleshooting, repairing, aligning, calibrating, and rebuilding multi-system avionics complexes consisting of multiple completely integrated electronic avionics systems where the complex accomplishes a number of major functions.

NOTE ONE: For the WG-2610-12 ANG Dual Status Technician positions, the mandatory military training requirements are the completion of an Air Force Three Skill Level Technical Training School and successful On-the-Job training that will result or resulted in the award of a compatible Five Skill Level AFSC. (Must upload supporting documentation)

SPECIALIZED EXPERIENCE: WG-13 must have at least a Seven-Skill Level in one of the compatible AFSCs, and at least 12 months of specialized experience in the WG-2610-12 level, experience which demonstrates of knowledge and skills to install, modify, overhaul, maintain, troubleshoot, repair, align, calibrate, and rebuild multi-system avionics complexes consisting of multiple completely integrated electronic avionics systems where the complex accomplishes a number of major functions.

NOTE TWO: For the WG-2610-13 ANG Dual Status Technician positions, the mandatory military education requirements are the completion of an Air Force Seven Skill Level Technical Training School and awarded a compatible Seven Skill Level AFSC, along with the successful completion of at least one military professional education course program. (Must upload supporting documentation)

MULTIPLE LEVEL RECRUITMENT: This position is being advertised using multiple level recruitment to allow for consideration of applicants with the basic skills necessary to develop to the full journeyman level of the position. If a less than fully qualified applicant is selected, incumbent may be trained and developed until proficiency is gained to full journeyman level. If less than fully qualified individual is selected for this position, the position has potential to Grade WG-13.

Education

ANG ENLISTED: To qualify an enlisted applicant for hire consideration into an ANG Dual Status Technician FWS 2610 position, award of the compatible Air Force Specialty Code, Craftsman Seven Skill Level; Journeyman Five Skill Level; or, the Apprentice Three Skill Level, with the position's compatible unit position assignment and a high school diploma, are mandatory requirements. Completion of high school courses in physics, algebra, trigonometry, and computer principles is desirable. Higher academic college courses and degrees that are aligned within the FWS Series 2610 type of work tasks are also desirable.

If you are using Education to qualify for this position:

You must provide transcripts or other documentation to support your Educational claims. To receive credit for Education, you must provide documentation of proof that you meet the Education requirements for this position.

Similar jobs you might like